|
EFLOW4N8D POWER SUPPLY12/24VDC 4-AMP
|
EFLOW4N8D POWER SUPPLY12/24VDC 4-AMP
eFlow4N8D is a power supply/charger that converts a 120VAC, 60Hz input into eight (8) PTC protected 12VDC or 24VDC power-limited outputs.
Input:
120VAC, 60Hz, 3.5 amp.
Input fuse: 5A/250V.
Output:
Eight (8) PTC protected power-limited outputs.
12VDC or 24VDC selectable output.
12VDC or 24VDC @ 4.0 amp supply current.
Outputs are rated @ 2 amp.
Auxiliary power-limited output rated @ 1 amp (unswitched).
Over Voltage Protection.
Battery Backup:
Built-in charger for sealed lead acid or gel type batteries.
Maximum charge current 1.54 amp.
Automatic switch over to stand-by battery when AC fails. Transfer to stand-by battery power is instantaneous with no interruption.
Supervision:
AC fail supervision (form "C" contacts).
- Notification trigger is selectable for 30 seconds (factory set) or 2 hours.
Battery fail & presence supervision (form "C" contacts).
Low power shutdown. Shuts down DC output terminals if battery voltage drops below 71-73% for 12V units and 70-75% for 24V units (depending on the power supply). Prevents deep battery discharge.
Fire Alarm Disconnect:
Supervised Fire Alarm disconnect (latching or non-latching) 10K EOL resistor. Operates on a normally open (NO) or normally closed (NC) trigger.
Electrical:
Operating temperature: 0° C to 49° C ambient.
BTU/Hr.:
12VDC: 24.57 BTU/Hr.
24VDC: 49.15 BTU/Hr.
System AC input VA requirement: 420VA.
Visual Indicators:
Green AC Power LED indicates 120VAC present.
AC input, DC output and Battery LED indicators.
Additional Features:
Short circuit and overload protection.
Unit is complete with power supply, enclosure, battery leads and cam lock
eFlow4N8D is a power supply/charger that converts a 120VAC, 60Hz input into eight (8) PTC protected 12VDC or 24VDC power-limited outputs.
Input:
120VAC, 60Hz, 3.5 amp.
Input fuse: 5A/250V.
Output:
Eight (8) PTC protected power-limited outputs.
12VDC or 24VDC selectable output.
12VDC or 24VDC @ 4.0 amp supply current.
Outputs are rated @ 2 amp.
Auxiliary power-limited output rated @ 1 amp (unswitched).
Over Voltage Protection.
Battery Backup:
Built-in charger for sealed lead acid or gel type batteries.
Maximum charge current 1.54 amp.
Automatic switch over to stand-by battery when AC fails. Transfer to stand-by battery power is instantaneous with no interruption.
Supervision:
AC fail supervision (form "C" contacts).
- Notification trigger is selectable for 30 seconds (factory set) or 2 hours.
Battery fail & presence supervision (form "C" contacts).
Low power shutdown. Shuts down DC output terminals if battery voltage drops below 71-73% for 12V units and 70-75% for 24V units (depending on the power supply). Prevents deep battery discharge.
Fire Alarm Disconnect:
Supervised Fire Alarm disconnect (latching or non-latching) 10K EOL resistor. Operates on a normally open (NO) or normally closed (NC) trigger.
Electrical:
Operating temperature: 0° C to 49° C ambient.
BTU/Hr.:
12VDC: 24.57 BTU/Hr.
24VDC: 49.15 BTU/Hr.
System AC input VA requirement: 420VA.
Visual Indicators:
Green AC Power LED indicates 120VAC present.
AC input, DC output and Battery LED indicators.
Additional Features:
Short circuit and overload protection.
Unit is complete with power supply, enclosure, battery leads and cam lock
